I. Panel
Panel diagram of OptiX 155/622H Metro1000 SS42ET1
Figure 1
Panel diagram of OptiX 155/622H Metro1000ET1/ET1O/ET1D/EF1 single boards
| Indicator Name | Status | Meaning |
|---|---|---|
| ALM-Red Alarm Lamp | Long off | No alarm occurs on the board |
| Blinks 3 times every second | Emergency alarm occurs on single board | |
| Blinks 2 times every second | Important alarm occurs on single board | |
| 1 flash every second | Minor alarm occurs on single board | |
| Long light | Self-test failure | |
| RUN-Green run light | Blinks 5 times per second | Single board is offline |
| Blinks 1 time every 1 second | Single board is in normal operation state | |
| Ethernet interface connection status indicator (green) | Long light | Successful connection of network cable/fiber optic and interface |
| Long off | Network cable/fiber optic connection to the interface failed | |
| Ethernet interface data send/receive indicator (orange) | Long on or blinking | Network interface is sending and receiving data |
| Long off | No data is being sent or received by the network interface |
| Single-board features | Metro1000 SS42ET1 | Metro1000 SS42ET1O | Metro1000 SS42ET1D | Metro1000 42EF1 | |
|---|---|---|---|---|---|
| Number of FE Electrical Interfaces | 8 | 8 | 2 | 4 | |
| Number of FE optical interfaces | - | - | - - - - - - - - - - - - - - - - - - - - - - - | 2 | |
| Connector Type | RJ-45 | RJ-45 | RJ-45 |
Electrical: RJ-45 Optical: LC |
|
| Operating Mode | Electrical Interface | Self-Negotiating, 10M/100M Full-Duplex, 10M/100M Half-Duplex | Self-Negotiating, 10M/100M Full-Duplex, 10M/100M Half-Duplex | Self-Negotiating, 10M/100M Full-Duplex, 10M/100M Half-Duplex | Self-Negotiating, 10M/100M Full-Duplex, 10M/100M Half-Duplex |
| Optical Interface | - - - - - - - - - - - - - - - - - - - - - - - | - - - - - - - - - - - - - - - - - - - - - - - | - - - - - - - - - - - - - - - - - - - - - - - | 100M full duplex | |
| Package Protocol | ML-PPP | ||||
| SDH Side VC-4 Bandwidth | 1×VC4 | 1×VC4 | 1×VC4 | 1×VC4 | |
| Binding bandwidth | 48×E1 | 48×E1 | 16×E1 | 48×E1 | |
| Number of VCTRUNK | 16 | 16 | 16 | 16 | |
| Layer 2 Switching | -Layer 2 Switching | Support | Supported | Supported | |
| VLAN | Supported | Supported | Supported | Support | |
| EPL | Support | -EPL | Support | - | |
| EVPL | -EVPL | - | - - | -EPLAN | |
| EPLAN | -EPLAN | Support | Support | Support | |
| EVPLAN | -EVPLAN | EVPLAN - | - - - - - - - - - - - - - - - - - - - - - - - | - - - - - - - - - - - - - - - - - - - - - - - | |
| Spanning Tree | - - - - - - - - - - - - - - - - - - - - - - - | Support | Support | Support for | |
| IGMP-SNOOPING | IGMP-SNOOPING | Support | Supported | Support | |
| RMON | Supported | Supported | Supported | Supported | |
| Parameter | Description |
|---|---|
| Interface rate | 10Mbit/s, 100Mbit/s |
| Access capacity |
ET1/ET1O: 8 x 10M/100M electrical signals ET1D: 2 x 10M/100M electrical signals EF1: 4×10M/100M electrical signals |
| Line code type | Manchester coded signal (10M) or MLT-3 coded signal (100M) |
| Connector Type | RJ-45 |
| Electrical Interface Specification | Conforms to IEEE 802.3 recommendations |
| Parameter | Description | |||
|---|---|---|---|---|
| Interface rate | 100Mbit/s | |||
| Line code type | MLT-3 coded signal | |||
| Optical interface type | S-1.1 | Ie-1 | S-1.1 | Ie-1 |
| Fiber Type | Singlemode LC | Singlemode LC | Singlemode MT-RJ | Multimode MT-RJ |
| Center wavelength (nm) | 1310 | 1310 | 1300 | 1300 |
| Maximum transmission distance (km) | 15 | 2 | 15 2 | 2 |
| Transmit optical power (dBm) | -15 to 8 | -19.5 to 14 | -15 to -8 | -19 to 14 |
| Receiving sensitivity (dBm) | -31 | -31 to -29 | -31 -29 | 31 -29 -31 |
The ET1/ET1O/ET1D/EF1 single boards have single board indicators, interfaces, and barcodes on the panel.
The panel of the ET1/ET1O/ET1D/EF1 single board is shown in Figure 1, where the optical interface of the EF1 single board is taken as an example of LC optical interface.
The ET1/ET1O/ET1D/EF1 single board panel has single board status indicators and Ethernet interface connection status indicators, and the descriptions of the indicators are shown in Table 1.
The ET1/ET1O/ET1D/EF1 single board has RJ-45 type electrical interface on the panel for sending and receiving 10M/100M Ethernet electrical signals.
The EF1 board also has MT-RJ/LC type optical interfaces on the panel for sending and receiving 100M Ethernet optical signals.
The ET1/ET1O/ET1D/EF1 single board completes the access of 10M/100M Ethernet service, supports various Ethernet service types, and realizes EOS (Ethernet over SDH) function.
OptiX 155/622H Metro1000 SS42ET1 is an 8-channel 10M/100M Ethernet electrical interface board.
The functions and features of the ET1/ET1O/ET1D/EF1 boards are shown in Table 1.
The ET1/ET1O/ET1D/EF1 single board also has the following features:
The ET1/ET1O/ET1D/EF1 single-board technical specifications include interface specifications, single-board size, single-board weight, and power consumption.
The electrical interface specifications of the ET1/ET1O/ET1D/EF1 single board are shown in Table 1.
The optical interface specifications of the EF1 single board are shown in Table 2.
The mechanical metrics for the OptiX 155/622H Metro1000 ET1/ET1O single board are as follows:
The mechanical metrics of the OptiX 155/622H Metro1000 EF1 single board are as follows:
The mechanical specifications for the OptiX 155/622H Metro1000 ET1D veneer board are as follows:
The maximum power consumption of the ET1/ET1O veneer boards at room temperature (25°C) is 26.1W.
Chinese
English
