:cm-set-neid:0x09000a; //设置网元ID
#ID:lognew: "szhw", "nesoft"; //Login the newly created network element
#ID:login:"szhw","nsesoft"; //登录现有
:cm-get-ip; //View IP
:cm-get-subnet; //查看子网号
:cfg-get-subnetlen:Bid; //Subnet number length
:cfg-get-subnetbd:Bid; //光口所服务的子网号
:cm-get-lanroute; //Ethernet routing
:cm-get-submask; //子网掩码
:cm-get-neid; //ID
:cm-get-nodeid; //nodeid
:cfg-:cm-get-nodeid; //nodeid
get-nename; //network element name
:cfg-get-neposition; //网元位置信息
:cfg-get-devicetype; //device type
:ecc-get-route; //查询ECC路由
:cm-get-curdata; //query the current alarm
:alm-get-hisdata; //查询历史告警
:cm-edit-user:user="huawei",password="hw" add congestion
:sm-add-user:"huawei","huawei123","admin",enable; 0sn9500
:cm-get-maccon; query the:sm-add-user:"huawei","huawei123","admin",enable; 0sn9500
ECC link light is good or not
主机软件、BIOS 检查，并检查两套主机软件是否一致,并确认当前是否运行在第一套主机软件。
:sys-get-nesoftver; //two host software versions
:sys-get-testver; //主机测试版本
:sys-get-ptsoftver; //host platform version
:ver; //主机软件、FPGA、BIOS
:cfg-get-bdinfo:11;


单板版本检查。要求单板软件版本、FPGA版本、PCB版本、单板BIOS版本符合版本配套表要求，且符合组网要求；
:cfg-get-bdversion:Bid; //single board software, FPGA, PCB
:cfg-get-bdverinfo:Bid; //单板软件、BIOS、FPGA、PCB

Network element state checking , net element is in running state
:cfg-get-nestate; //查询网元状态
Net element time check. The time of the network element is consistent with the time of the network management; the time deviation between the network elements is generally within 5 minutes;
:date; //查询网元日期
:time; //query the time of the network element
主机复位记录检查。主机异常复位低于1次/月。
:errlog; //query the host reset log
:mon-get-errlog:Bid; //查询单板复位记录
Board configuration check. Requires that the single board type is correct and the logical board position should match the actual board installation.
:cfg-get-board; //逻辑板位安装
:cfg-get-phybd; //Physical board position
环回检查。正常情况下，所有通道不允许设置环回，注意检查备用通道设置. 用网管检查单板通道、光口环回情况；//查询告警时，不允许出现loop_alm告警；
Official information check. The official telephone number is set correctly, the length of the number is consistent, and the dialing test is carried out on site, and the call waiting time is defaulted to 9. The use of the optical port is set correctly; the corresponding electrical characteristics of the official business are consistent with the actual configuration. The official automatic protection reversal is enabled by default.
:cfg-get-telnum:51; //选址呼叫电话
:cfg-get-meetnum:51; //Conference phone
:cfg-get-reqtime:51; //呼叫等待时间
:cfg-get-tellen:51;
:cfg-get-lineused:51;
:cfg-get-meetlineused:51;
:cfg-get-dataport:51, OhSlot; //广播数据口的时隙及广播源宿
:cfg-get-f1port:51; //F1 through upstream and downstream ports
:cfg-get-porttype:51; //复用口为串口或广播数据口
:cfg-get-portmode:51; //Serial or data port:cfg-get-porttype:51; //复用口为串口或广播数据口
electrical characteristics
网元安全检查，网元用户的设置，多台网管需要创建不同的网元用户。
:sm-get-alluser; //Status of all network element user tasks. No suspend tasks.
:sys-get-alltaskinfo; //网元一致性校验周期。缺省为300s。
:cfg-get-bdchecktime; //Operational consistency check.
:cfg-get-xc:0,0; //查询配置的交叉连接
:cfg-get-xcconect:0,0; //Query the actual generated cross-connections
:cfg-get-nelowxc:Xcl_bid,0,0; //主机侧低阶业务一致性检查
:cfg-get-bdlowxc:Xcl_bid,0,0; //Low-order service consistency check on the single board side
:cfg-get-calcmode; //交叉矩阵下发模式，缺省为increment
:cfg-get-ohconnect:0,0; //Overhead service. Matches configuration (one per protection group, two per quad fiber ring)

:cfg-get-als:Bid,Pid; //激光器自动关断标志。线路板缺省disable；光放板缺省enable。
:cfg-get-laser:Bid,Pid; //Laser switch status, on.
:cfg-get-loop:Bid,Pid; //光口环回模式 环回模式，不环回。
:cfg-get-vc4loop:Bid, Pid, AU4Id; //Channel loopback mode
:cfg-get-autoclear:au4loop; //通道环回自动解除，环回解除模式，使能，缺省5min。
:cfg-get-autoclear:portloop; //Optical port loopback auto-unlocked
:cfg-get-autoclear:ethloop; //以太网端口环回自动解除

:cfg-get-synclass:Bid; //Clock configuration data check. Requires correct clock tracking level, external clock synchronization quality information byte location, and clock ID configuration data.
当前时钟源查询。正常情况下当前跟踪源为最高优先级时钟。
:cfg-get-cursyn:Bid; //current tracking source check current clock source inversion status, including inversion mode.
:cfg-get-synswstate:Bid; //时钟源倒换状态
S1 byte mode setting. It should match the clock grouping.
:cfg-get-s1mode:Bid; //S1字节模式//对于需要启动S1字节的时钟组网，查询结果应该为enable，否则为disable。
Whether the clock source recovery parameter is set to "Advanced Clock Source Auto Recovery" Check with the network administrator or use the command line
:cfg-get-syncnorvt:Bid; // 返回disable 是可恢复；enable是不可恢复
:cfg-get-synwtrtime:Bid; Query the clock source recovery waiting time, the requirement is the default value of 5 minutes.
:cfg-get-insynmode:Bid;有外部输入或输出时钟的，需要检查输入或输出时钟源模式。
:cfg-get-outsynmode:Bid;//External input/output clock mode with bit and hz
:cfg-get-cursyns1:Bid;当前跟踪源及对应的S1字节。全网一致。
:cfg-get-syns1id:Bid;S1 byte clock source ID. clock ID is set reasonably.

:cfg-get-alls1:Bid;优先级表中所有源对应的S1字节。合理且与配置相符。
:cfg-get-stgworkmode:Bid;Clock board current work mode. It is trace mode .
:cfg-get-synexist:Bid,0;当前存在的时钟源与实际时钟源一致。
:cfg-get-synenable:Bid;Clock source enable state, enable.
:cfg-get-mans1qua:Bid,0;人工配置时钟质量。和配置一致。
:cfg-get-synswstate:Bid;Clock source inversion state. Not inverted.
:cfg-get-exts1insertslot:Bid,0xf001;外部源S1字节插入时隙。和实际插入时隙一致
:cfg-get-exts1insertslot:Bid,0xf002;

未正式上业务前的DPS倒换测试，要求可以正常倒换。
:cfg-get-dpsstate:Pgid; //Confirm the master-standby relationship with this command before inverting.
:cfg-set-dpsswitch:Pgid,DstBid;

:cfg-get-sncpprotmode; SNCP node protection mode setting check. The query result should be SNCP protection
:cfg-get-sncppg; //子网保护组，子网连接保护组的检查，应正确设置。
//The query comes out as the following PgId
:cfg-get-sncppgpara:PgId; //查询，查询恢复模式，等待恢复时间，一般恢复时间设置为600s。 恢复模式，等待恢复时间
Optical port mapping relationship check. Optical port channel and service level mapping is correct, to configure the opt-in, i.e., both primary and backup channels should be mapped. :cfg-get-sncpbdmap:PgId; // Optical port mapping
SNCP保护组属性的检查。工作和保护通道都要设置，倒换条件设置正确。
:cfg-get-sncpattrib:PgId,PuId; // Protection group attributes, inversion conditions
SNCP保护状态的检查。工作源、保护源业务状态正常。
:cfg-get-sncpstate:PgId; // Current state
SNCP双发业务检查。双发的业务需要配置双发，系统不能自动复制。
:cfg-get-xcconnect:Bid,0;
:cfg-get-bdlowxc:Xcl_bid,0,0; //业务检查
//:cfg-get-bdlowxc:Xcl_bid,0,0; //业务检查
Query the single board service configured with SNCP service to check if it is configured with dual-issue
开销模式检查（155M SNCP业务）。155M业务全路径开销模式设置为穿通方式。0-强制终结,1-强制透传。
:cfg-get-vc4mode:Bid, Pid, AU4id; //Host-side overhead passthrough mode.
业务配置数据检查。对于2M SNCP业务，通过SNCP节点时不能采用VC4形式穿通。
:cfg-get-xc:Bid,0;
:cfg-get-nelowxc:Xcl_bid,0,0; //检查业务配置。
Complex networking configuration data check. For example, DNI, SNCP intersecting ring, SNCP with 1 + 1 protection chain and other group networks with correct service configuration routing. :cfg-get-xc:Bid,0;

:cfg-get-sncpreport:PgId; 保护组倒换状态，enable。

Protocol type query. Requires network elements on the same ring to use the same protocol.
:cfg-get-rmsprtcl:PgId; //查询协议类型。
The multiplexed segment protection group check should be set correctly.
:cfg-get-rmspg; //复用段保护组
// The query comes out as the following PgId
复用段参数检查，检查节点参数正确、倒换恢复时间的设置，一般设置为600s。
:cfg-get-rmsattrib:PgId; //Multiplexed Segment Attribute
:cfg-get-rmsbdmap:PgId; //板位映射，复用段板位映射的检查，板位映射应该正确无误。
:cfg-get-rmsstate:PgId; //Multiplexed Segment State, Multiplexed Segment Inversion State checking, Multiplexed Segment State should be normal.
:cfg-get-rmssdflag:PgId; //信号劣化标，复用段保护组劣化标志的检查，应设置为Enable。 志
Multiplexed segment inversion event. No new abnormal inversion events.
:cfg-get-rmsevent:PgId; //倒换事件
Multiplexing segment ring protection channel lock status
:cfg-get-rmslock:PgId; //锁定状态
According to the actual situation, practice inversion or fiber break inversion test. It is required that the whole network can migrate normally when practicing the switchover, and it is required that the switchover and recovery can be carried out normally without affecting the service when the fiber is cut off. If the bureau permits, conduct the reversal test.

线性复用段保护组的检查，应正确设置。
:cfg-get-lmspg; //protection group
//查询出来的即为下面的PgId
Linear multiplexing segment parameter checking, pay attention to the setting of the reversal recovery time, generally set to 600s.
:cfg-get-lmsattrib:PgId; //线性复用段属性
Linear multiplexing segment protection group unit optical port mapping relationship checking.
:cfg-get-lmsbdmap:PgId; //光口映射关系
:cfg-get-lmsstate:PgId; //Linear multiplexing segment state, linear multiplexing segment inversion state check, the state should be normal.
:cfg-get-lmssdflag:PgId; //信号劣化标志，线性复用段保护组劣化标志的检查，应设置为Enable。
:cfg-get-lmsevent:PgId; // Inversion event, linear multiplexed segment inversion event. No new abnormal inversion events have been added.
线性复用段业务配置检查。需要保护的业务必须配置在主用系统上。1＋1单端倒换应该配置为双发 :cfg-get-xc:0,0;
:cfg-get-nelowxc:Xcl_bid,0,0; //Query business configuration
根据实际情况，进行练习倒换或断纤倒换测试。要求练习倒换时全网能够正常状态迁移；断纤倒换时要求能够正常倒换和恢复、不影响业务。 在局方允许的情况下，进行倒换测试。
:dbms-copy-all:mdb,drdb;
:dbms-copy-all:drdb,fdb0;
:dbms-copy-all:drdb,fdb1;
数据库比较。mdb，drdb，fdb0，fdb1应该一致。（USER.DBF和perstate.dbf除外）
:dbms-compare-all:mdb,drdb;
:dbms-compare-all:drdb,fdb0;
:dbms-compare-all :drdb,fdb1; //compare databases
数据库保护模式。不能工作于保护模式。工作模式返回值应为normal，数据库保护模式状态应为enable，保护模式写权限应为disable。 :dbms-get-mode; //查询数据库当前工作模式，返回normal-正常模式 protect-保护模式
:dbms-get-pmodestate; //query database protected mode status
:dbms-get-pmodewright; //查询数据库保护模式写权限
Database backups. Database automatic backup and cycle backup enable; backup cycle 30min not too long.
:dbms-get-autobackup; //数据库自动备份状态
:dbms-get-cyclebackup; //Cycle backup allowed flag
:dbms-get-backupperiod; //数据备份周期

Alarm query. No temperature and other abnormal alarms, line signal loss, clock alarms, reverse alarms need to find out the reason.
:alm-get-curdata:0,ALL;
:alm-get-hisdata:0,ALL;
性能查询。要求无异常性能事件，温度正常，光功率与开局光功率记录无大的变化。
:per-get-curdata:0,0,0,0,0,perall,15m;
:per-get-hisdata:0,0,0,0,perall,15m,1,16;
:per-get-curdata:0,0,0,0,0,perall,24h;
:per-get-hisdata:0,0,0,0,perall,24h,1,6
Performance parameter setting. 15m/24h performance monitoring start time should be the specific start time; 15m :per-get-hisdata:0,0,0,0,perall,24h,1,6
/24h performance end start time should be None.
:per-get-starttime:15m;
:per-get-starttime:24h;
:per-get-endtime:15m;
:per-get-endtime:24h;
:per-get-interval;监视周期间隔。不小于60s。

ECC routing check. Normally, ECC should take the shortest route and reach all network elements. The number of network elements reachable by forwarding through this network element :cm-get-eccroute; // ECC routes, the number should not exceed 50 in general to avoid ECC oscillation.
:cm-get-maccon; //ECC的MAC层连接，ECC手工配置检查。除非特殊情况，不允许手工配置ECC。
:cm-get-bdinfo; Disable the ECC function of the STM-N interface connected to the trunk.
:cm-get-fiberport:Bid,Port;光板光口状态和DCC速率。关闭不必要的光口速率。
:cm-get-chaninfo:Chan; Channel send/receive packet information. Sends and receives packets normally.
:cm-get-chanerror:Chan;通道错误信息。无错误信息。

:cfg-get-voltlevel:52;Rated voltage type, 48V or 60V.
:cfg-get-voltalmpoint:52,VoltType;电压门限，VoltType选48V或60V。48v缺省为600~410。
:cfg-get-involt:52,PIUNO;Current power supply voltage value, within threshold.
:cfg-get-bdtemp:Bid;单板当前温度，门限范围之内。
:cfg-get-bdtempth:Bid;Single board temperature threshold, line and crossover: 500~0, others: 400~0.
:cfg-get-envtempthrd:52;环境温度门限，缺省400~0。
:cfg-get-envtemp:52;Current ambient temperature, within threshold.
:optp:34,0,66,1,ff,25,bid(16进制);MBUS的版本，版本正确，一致。
:optp:34,0,66,1,12,31,bid(hexadecimal);MBUS monitored veneer voltage value, consistent with the actual voltage value, with a deviation of no more than 5%.
:optp:34,0,66,1,12,25,bid(16进制);
:optp:34,0,41,1,ff,53;Fan speed, the difference of each fan speed is small.

:cfg-get-pumplasersw:Bid,Pid,Pathid;查询泵浦激光器开关状态，状态正确。
:cfg-get-adtype:Bid;Query A/D chip type, chip type is correct.
:cfg-get-oatype:Bid;查询光放板类型，光放板类型正确。
:cfg-get-paralist:Bid,Pid;Query the performance value list of optical amplifier board, the performance is normal.

查询 LMP 的信息。使用的控制通道状态为UP且有正确的远端信息、使用的数据链路和TE链路有正确远端信息。
:lmp-get-ccbyport:0,0; //Query the control channel
:lmp-get-tel:0,0; //查询 tel 链路
:lmp-get-dbl:0,0; //Query the dbl link
查询路由的信息 :ospf-get-treeinfo:2; //查询TE链路信息，注意数量是否有变化
:ospf-get-ctrltopo:0,0.0.0.0; //Show the topology information of the control plane
:ospf-get-linktopo:0.0.0.0; //显示传送平面TE链路信息，包含全网链路信息；SRLG跟配置一致
:rtm-get-route; //Query the information of the routing table, there are routes for the whole network
:rtm-get-fib; //查询转发路由表的信息，全网都有路由
Query the information of signaling :mpls-get-mlsp:all;//Query the information of the service (network management interface)
:mpls-get-smlsp:all;//查询业务的信息，注意业务Flag状态是否为Normal
:mpls-get-smlsp:src;//Query the information of the service (with this node as the first node), pay attention to the number of the service
:mpls-get-smlsp:dst;//查询业务的信息（以此节点为末节点），注意业务数量
:mpls-get-if:all;//Query the status of the interface that is obtained by the signaling, pay attention to the status of the interface whether the interface is up or not. 0x07
:mpls-get-rcvytime;//查询等待恢复时间，缺省为720分钟
:mpls-get-rsttime;//query the recovery time of recoverable reroute, default is 10 minutes
:mpls-get-exctype;//查询排除类型，缺省为exclink －排除链路查询 SC 的信息
:sc-get-dbl:0,0; //query the data link information
:sc-get-lspcb-info:0.0.0.0,0.0.0.0,0; //查询LSP控制块一般信息，注意数量与信令查询业务的数量一致
:sc-get-lspcb-exinfo:0; //query the LSP control block extension information, note whether treetype is 1
:sc-get-port-xcinfo:0,0,0,0; //查询光口之间的交叉信息
:cm-:sc-get-port-xcinfo:0,0,0,0; //查询光口之间的交叉信息
get-bdinfo; //Query the status of the optical interface of the active board
:cm-get-interface; //查看当前路由表的全部信息
:lim-get-ctrllink:0; //Query the information of the control interface, the PPP interface enables the OSPF protocol, the Ethernet interface does not enable the OSPF protocol
:lim-get-telinkinfo:0; //Query TE link details